Solid Dye Laser Rods 585nm, 595nm, 650nm, 660nm-manufacture,factory,supplier from China

After more than one year’s research work, WISOPTIC has successfully developed two types of dye laser cells – 585nm and 650nm.With advanced technique of coating and optical system design, dye laser headpiece has been developed and will be in mass production soon.Dye laser headpiece 585nm is used mainly to treat facial telangiectasia, and dye laser headpiece 650nm for removal of green tattoo, etc.Dye laser headpiece made from WISOPTIC has higher conversion efficiency than that of any competing product.

Experimental SetupIn order to obtain a 266 nm deep ultraviolet laser with high efficiency and stable operation, this paper built an all-solid-state 266 nm deep ultraviolet laser generation device as shown in Figure 1, which consists of a cavity-dumped all-solid-state Nd:YVO4 laser, a double-frequency system, and a quadruple-frequency system.Fig.

2-5 μm mid-infrared laser crystals have important applications in directional infrared countermeasures, anti-terrorism, biomedicine, environmental monitoring, optical communications, strong field physics, laser fusion, and mid-to-far infrared (nonlinear frequency conversion) basic light sources, etc. With the related development of the pump source technology of semiconductor laser (laser diode, LD), solid-state laser and fiber laser (including resonant pump), mid-infrared crystal has become one of the four main laser crystals developed currently.

1. 2   ~ 2.3 μm laser crystals doped with Tm3+ Compared with the 2 μm band (3F4 → 3H6) of Tm3+, the 2.3 μm laser operation based on the 3H4 → 3H5 transition of the Tm3+ doped laser medium has the following advantages: (1) ~790 nm LD is directly pumped to the upper energy level of the laser. Tm3+ has a strong absorption around 790 nm (directly corresponding to the 3H4 → 3H6 transition), which can match the emission wavelength of the current mature commercial AlGaAs LD, so as to realize high-performance LD pumping all-solid-state high-efficiency 2.3 μm laser operation.

Introduction High-power all-solid-state deep ultraviolet (DUV) lasers have many important applications in scientific research, medical diagnosis, and industrial manufacturing, such as Raman spectroscopy, photobioimaging, integrated circuit etching, and precision micromachining, due to their compact structure, high single-photon energy, and good long-term stability.

Introduction 532nm solid-state lasers are widely used in industry and medicine. In the field of scientific research, continuous, high-stability 532nm green light and kilohertz, high-energy nanosecond 532nm laser are the most ideal pump source solutions for titanium sapphire oscillators and amplifiers respectively. The basic route is to use an 808nm/880nm semiconductor laser as the pump source, generate a 1064nm laser in an Nd:YVO4 or Nd:YAG crystal, and then perform frequency doubling (SHG) through a frequency doubling crystal to generate a continuous or pulsed 532nm laser.

Nanoscale laser damage precursorsDifferent from microscopic defects, defects are called precursors here. Defects generally refer to observable microstructures that are different from the characteristics of the surrounding matrix materials, and are often observed by optical microscopy. The precursors mentioned in this article generally cannot be directly observed by optical methods, and there is no obvious difference in characteristics from the surrounding matrix materials.

Based on the basic principles of laser damage, researchers have found a breaking through point to solve the problem of laser damage to optical components. But it is very difficult to effectively suppress the source of laser damage in the manufacturing process. Given the variety and complexity of the manufacturing process of optical components, it is necessary to establish the link between the defect formation and the manufacturing process.

1. Research status and future development trend of mid-infrared (2-5 μm) laser crystalsAccording to the order of laser wavelength from short to long, the main material that have achieved laser output (including some optical fibers and transparent ceramics for comparison) are listed in Table 1. Among them, the highest continuous laser output power of laser crystals corresponding to different wave bands is shown in Figure 2. The laser output power of activated ions shows an obvious attenuation trend as the wavelength expands to the mid-infrared direction.

Since defects induce laser damage, and defects are randomly distributed in optical components, the detection and evaluation of laser damage performance of optical components has become another important research content. The standard for laser damage threshold testing was established in the 1990s and has been continuously improved with the development of laser technology and optical materials.